City Greens outdoor NFT Hydroponics kit is a perfect choice for people who wish to experiment or try out hydroponics at home on a medium scale. Using completely food-safe and lead-free plastic makes it one of the best kits available in the market with such exceptional quality. You can easily start hydroponic farming or vertical farming with this kit as it contains all the hydroponics accessories required. The kit comes in two variants 24 planter and 40 planter.
What are the contents of an outdoor NFT hydroponics kit?
- Food-grade NFT channels
- Plumbing pipes and connections
Stand- Reservoir (Nutrient tank)
- Submersible pump
- Digital timer
- Air pump with air stone
- Food-safe net pots
- Fly-ash leca
- Hydroponic nutrients
- Seeds
- Seed germination plugs
- pH Up & pH Down
1. How to Assemble Outdoor NFT Hydroponics Kit?
- Place the NFT channels on the stand and fix all the plumbing pipes.
- Place the submersible pump in the reservoir tank and connect the pump to the plumbing pipe with a valve, that supplies water into the NFT channels.
- Bring an electrical board near the kit with at least two sockets.
- Connect the submersible pump's power plug to the timer and then fix the timer into the power socket. (the timer runs the pump at programmed times)
- Insert the transparent air tube into the reservoir through the lid. Attach the air stone to this end of the tube.
- Attach the other end of the tube to the air pump. Place the air pump outside the NFT set up in a dry area and connect the plug to the power source.
2. How to Start Growing Plants
There are 4 simple steps involved in growing plants from seeds. Seed germination, Hardening the sapling, Transplanting, Monitoring & Maintenance.
a. Seed Germination
1. Place one seed germination plug in each net pot without removing the outer cover. Then add 30 to 50 ml water to the plug to expand it completely.
2. Sow 3-4 seeds around 1/2 cm deep in the germination plug. Place the net pots in a tray or plate and keep the tray in a warm and dark place to speed up the germination process.
3. Keep the germination plug moist by spraying 5 - 10 ml of water once or twice a day (depending upon the weather in your area). The seeds will start to germinate in 3 to 7 days time.

b. Hardening
- Once the seeds have germinated, start exposing them to morning and evening sun for couple of hours a day. And increase sure the exposure gradually.
- Provide 10 - 15 ml of (regular or nutrient) water to the saplings everyday.
- For next 1 week, keep increasing the sun exposure gradually till the saplings develop 6-8 leaves.
- Once the sapling develops 6-8 leaves it is ready to be transplanted.
NOTE: Prepare a 500 ml nutrient solution by adding 1 ml each of N, K and P to 500 ml of water. Use this solution, once on alternate days to water your plants. Rest of the times use plain water.
c. Transplanting
1. Place the NFT system in an area that gets a good amount of sunlight. (Note that if the sunlight is not adequate the plants will not grow properly).
3. Connect the submersible pump plug to a power source directly and switch it on to run the pump for 3-5 minutes to ensure NFT channels are filled with nutrient water. Make sure to switch off the pump once the water starts to collect back in the reservoir.
- Once the NFT channels are filled with nutrient water connect the submersible pump to the timer and then the timer to the power source and supply power continuously.
- The timer should always be in Auto mode to run the pump automatically.
d. Monitoring & Maintenance
1. Aeration
2. Reservoir Water Level
Check the water level in the reservoir 2-3 times in a week and make sure the submersible pump is always inside water
3. Nutrient Addition
Add 1 ml of N, K, & P and 2 ml Greens, 1 ml Nutes in one liter of water. Use it to top up the reservoir when the water level is low.
4. Monitoring Plants
It's a best practice to monitor the plants health frequently. Regular observation enables early detection of diseases and pest
Common issues you might face while growing.
Common issues you might face while growing.
GERMINATION (LANKY GROWTH)
When the germinated seedlings are not kept under the light their stem becomes thin & long (lanky), eventually the growth is reduced and the plants may die. To avoid this provide sunlight in the mornings and evenings after germination when the sun is not harsh.
HIGH WATER TEMPERATURE
HIGH WATER TEMPERATURE
LACK OF DISSOLVED OXYGEN
Insufficient oxygen availability can lead to root suffocation and promote the growth of anaerobic bacteria, potentially causing root diseases and negatively impacting plant health. Make sure to use the air pump regularly to have optimal oxygen levels.
LEAKAGES AT JOINTS
No matter what there are times when you might need a helping hand in your growing journey. We are dedicated to providing excellent customer support. Our knowledgeable and friendly support team is available to assist you with any questions or issues you may have. Whether you need help with installation, troubleshooting, or any other aspect of using our product, we are here to help.